Our top 10, at a glance.
Choose a manual cutter for straight and diagonal backsplash cuts, matching tile material, thickness, scoring motion, support and accessories.
- #1RUBI SPEED-62 MAGNETRUBI SPEED-62 MAGNET
- #2QEP 24-inch Professional Tile CutterQEP 24-inch Professional Tile Cutter
- #3Montolit Masterpiuma P5 63P5XLMontolit Masterpiuma P5 63P5XL
- #4Sigma Series 4 NEX 4BNSigma Series 4 NEX 4BN
- #5RUBI TS-43MAXRUBI TS-43MAX
- #6RUBI TR-600 MAGNETRUBI TR-600 MAGNET
- #7Montolit MiniPiuma 26PBoxMontolit MiniPiuma 26PBox
- #8Sigma Series 4 UP 4BUSigma Series 4 UP 4BU
- #9RUBI STAR-42RUBI STAR-42
- #10RUBI TX-710MAXRUBI TX-710MAX
All 10 picks, in order.
- #1
RUBI SPEED-62 MAGNET
RUBI SPEED-62 MAGNET
A general-purpose push cutter with a mobile breaker
Why it fits
- SPEED-62 MAGNET is our first choice for a mix of ordinary ceramic and porcelain backsplash cuts. The selected US 14988 package lists a 24-inch straight cut and 17-3/8-inch-square diagonal capacity; check the tile’s actual orientation before ordering. Its magnetic mobile breaker works along the cut rather than at one fixed breaking point. The maker lists dual 20 mm rails, a side stop for repeat cuts and a supplied 8 mm scoring wheel. The selected package includes a case. RUBI’s metric sheet specifies a 3–15 mm thickness range. Choose a compatible wheel for the material; a longer rail and magnetic breaker do not establish a minimum strip width or successful snapping of every textured porcelain. Make trial cuts on the actual tile. [1] [2] [3]
Model: 14988; 62 cm version with case · One selected cutter and named package; sizes and case variants not counted separately. · US
- #2
QEP 24-inch Professional Tile Cutter
QEP 24-inch Professional Tile Cutter
A guided 24-inch cutter with support arms
Why it fits
- QEP 10630 is the choice for a buyer wanting side support and a simple rip/angle guide. Its feature section lists 24-inch straight cuts, 17.5-inch diagonal cuts and tile up to 1/2 inch thick, for most ceramic and porcelain. The current model has a 7/8-inch titanium-coated tungsten-carbide ball-bearing scoring wheel, dual chrome rails and a ball-bearing slide. QEP specifies replacement wheel 21125 and lists no carrying case. Confirm the current 10630 package rather than assuming legacy 10630Q contents. The linked manual calls for one continuous scoring pass with medium pressure, followed by the prescribed breaking position. It says to clean rails with a dry cloth and not oil them. QEP’s lower specification table conflicts with its diagonal feature figure; use 17.5 inches conservatively and confirm fit with the seller. [4] [5] [6]
Model: 10630; current US model · One selected cutter and named package; sizes and case variants not counted separately. · US
- #3
Montolit Masterpiuma P5 63P5XL
Montolit Masterpiuma P5 63P5XL
Adjustable scoring pressure and a folding angle guide
Why it fits
- Masterpiuma P5 is the pick for repeated cuts across different tile thicknesses. Select the 63P5XL row in Montolit’s linked technical sheet: 63 cm straight, 44-by-44 cm diagonal and 20 mm maximum thickness. The page also refers to the shorter 63P5 family name; verify the supplied model. The P5 frame has side supports, a folding square for angle cuts up to 45 degrees in either direction and a handle with pressure indicators. Its instructions describe scoring toward the measuring guide, then using the handle for separation. These features do not constitute our accuracy test. The manual includes handle adjustment and a lubricant-vial setup. MOSAKIT article 58 is an optional pad for the stated mosaic and delicate thin-glass applications; it is not assumed included. Match the accessory and tile instructions before using it on those materials. [7] [8] [9]
Before you choose
- This is the standard P5 family, not a claim about the separate P5 Italica; verify 63P5XL identification and accessory contents. [7] [8] [9]
Check before buying:
- This is the standard P5 family, not a claim about the separate P5 Italica; verify 63P5XL identification and accessory contents.
Model: 63P5XL; 63 cm entry in the linked technical sheet · One selected cutter and named package; sizes and case variants not counted separately. · US
- #4
Sigma Series 4 NEX 4BN
Sigma Series 4 NEX 4BN
A push handle with a suspended scoring wheel
Why it fits
- Sigma 4BN NEX is the push-handle specialist for a buyer considering structured tile. Sigma lists a 62 cm straight cut, 43.8 cm diagonal capacity and tile up to 19 mm thick. These are distinct from the dimensions of older NEX references. The 16 mm scoring wheel runs on roller bearings with double suspension, which Sigma positions for structured surfaces. A 120 mm breaker foot has a replaceable anti-mark pad; the carriage uses three double-row bearings. Its handle can stay raised while positioning tile. The suspended wheel is a design reason to consider NEX, not proof every relief or textured glaze will snap cleanly. Sigma lists the 64B2 magnetic mosaic mat as an accessory; do not infer that an unmodified cutter handles every sheet mosaic or glass tile. [10] [11] [12]
Before you choose
- Choose it for push-handle preference and the wheel design; sample cuts still decide whether a particular texture is suitable. [10] [11] [12]
Check before buying:
- Choose it for push-handle preference and the wheel design; sample cuts still decide whether a particular texture is suitable.
Model: 4BN; 62 cm push-scoring version · One selected cutter and named package; sizes and case variants not counted separately. · US
- #5
RUBI TS-43MAX
RUBI TS-43MAX
A compact cutter with a fixed breaking point
Why it fits
- TS-43MAX suits small-format tile when a compact professional frame matters more than long rails. Its maker sheet lists 43 cm straight cuts, 30-by-30 cm diagonal cuts and a 6–15 mm thickness range. Thin tile below that range needs another choice. The single-point fixed breaker distinguishes TS from RUBI’s mobile-breaker ranges. SMARTPOWER applies progressive breaking pressure; dual 17 mm rails sit over a steel base. RUBI lists 6 mm and 10 mm scoring wheels with the cutter and a case for the selected version. The maker positions TS for intensive ceramic and frequent porcelain cutting. Select the wheel and prescribed scoring/breaking setup for the tile. A fixed breaker and its force rating do not establish a usable minimum strip width or an edge finish on your particular backsplash. [13] [14] [15]
Model: 18972; grey case version · One selected cutter and named package; sizes and case variants not counted separately. · US
- #6
RUBI TR-600 MAGNET
RUBI TR-600 MAGNET
Repeated angled cuts using a swivelling square
Why it fits
- TR-600 MAGNET is our angled-layout choice when a swivelling measurement square is useful for repeat cuts. The selected US 17907 row lists 23-5/8-inch straight cuts and a 16.5-inch-square diagonal tile capacity, with a case included. The mobile breaker uses a magnet system for one-handed operation. The rotating square separates its layout workflow from SPEED’s side-stop arrangement. RUBI lists an 800 kg separating-force figure; this is a manufacturer rating, not a measured finish or accuracy result. Check the tile thickness and scoring-wheel match against the exact TR package. The selected row lists 1/8–5/8 inch, while the introduction says up to 9/16 inch. Confirm the permitted thickness in the model instructions before buying near either limit. Neither the swivelling square nor the breaker makes outlet notches a score-and-snap operation. [16] [17] [18]
Model: 17907; inch-scale version with case · One selected cutter and named package; sizes and case variants not counted separately. · US
- #7
Montolit MiniPiuma 26PBox
Montolit MiniPiuma 26PBox
Compact backsplash work with an optional mosaic pad
Why it fits
- MiniPiuma 26PBox is the compact kitchen-and-bathroom pick for smaller tile. Montolit’s technical table lists 36 cm straight cuts, 25-by-25 cm diagonal cuts and a 20 mm maximum thickness. The Box version is the selected package, not a second cutter recommendation. The small frame includes a protractor square for diagonal and repeat cuts. The maker lists the boxed version separately from the lighter unboxed 26P. Check storage dimensions and package contents rather than comparing the boxed weight with a bare competitor. Montolit describes optional MOSAKIT article 58 for glass, ceramic and porcelain mosaic applications. That accessory matters: the base cutter alone is not our recommendation for arbitrary mesh-backed or glass mosaics. Confirm tile and pad compatibility, and try the actual sheet before committing the layout. [19] [20] [21]
Before you choose
- The 36 cm rail limits long decorative tile; mosaic capability depends on the specified optional accessory and tile suitability. [19] [20] [21]
Check before buying:
- The 36 cm rail limits long decorative tile; mosaic capability depends on the specified optional accessory and tile suitability.
Model: 26PBox; 36 cm cutter with box · One selected cutter and named package; sizes and case variants not counted separately. · US
- #8
Sigma Series 4 UP 4BU
Sigma Series 4 UP 4BU
A pull handle for users who prefer that scoring motion
Why it fits
- Sigma 4BU UP is the pull-scoring alternative to NEX. Its current model row lists 70 cm straight cuts, 49.5 cm diagonal capacity and a maximum tile thickness of 17 mm. Choose the scoring direction deliberately rather than treating UP and NEX as size variants. The pull handle uses a 12 mm wheel and a 100 mm breaker foot with a replaceable anti-mark pad. Sigma lists three double-row carriage bearings and a raised handle position for placing tile. The visible wheel helps position the score line; we have not measured alignment accuracy. The 64B2 magnetic mosaic mat and front-measurement accessories are separate options. Their listing does not show every mosaic will work on the bare machine. Wheel, tile surface and operator motion still need to suit the work; a familiar push stroke may make NEX a better personal fit. [22] [23] [24]
Model: 4BU; 70 cm pull-scoring version · One selected cutter and named package; sizes and case variants not counted separately. · US
- #9
RUBI STAR-42
RUBI STAR-42
Basic ceramic subway tile and occasional porcelain
Why it fits
- STAR-42 is the simpler compact choice for a ceramic backsplash. Its maker sheet lists 42 cm straight cuts, a 30-by-30 cm diagonal tile and 12 mm maximum thickness. RUBI describes professional ceramic use and occasional porcelain work. The cutter has dual rails, a mobile multipoint breaker, a cast-aluminium base and a supplied 6 mm scoring wheel. Select reference 14946 for the case; reference 14943 is the alternative without it. Those packaging choices are one physical cutter family. Choose STAR for straightforward ceramic cuts within its size rating, rather than assuming the occasional-porcelain description covers repeated dense porcelain. Confirm a suitable replacement wheel and actual tile fit. The modest frame is a different purchase from TS’s fixed-breaker setup, even though their straight capacities are close. [25] [26] [27]
Before you choose
- Repeated hard-porcelain work and long planks are reasons to consider another cutter; the maker only positions porcelain use as occasional. [25] [26] [27]
Check before buying:
- Repeated hard-porcelain work and long planks are reasons to consider another cutter; the maker only positions porcelain use as occasional.
Model: 14946; 42 cm version with case · One selected cutter and named package; sizes and case variants not counted separately. · US
- #10
RUBI TX-710MAX
RUBI TX-710MAX
Longer or thicker tile shared with other renovation work
Why it fits
- TX-710MAX is the specialist upgrade when backsplash tile shares a tool with longer or thicker renovation material. The maker sheet specifies 71 cm straight cuts and 50-by-50 cm diagonal capacity. It is more equipment than an ordinary small subway-tile job needs. The mobile breaker has a ratchet lock and trigger release, with 30 mm tubular rails, floating tables, support arms and a pivoting square. The package includes 8 mm and 22 mm EXTREME PLUS scoring wheels and a case; check the PLUS wheel system when replacing them. The technical sheet distinguishes 3–19 mm tile with the protector from 3–21 mm without it. Plan around the protected 19 mm limit and follow the instructions rather than reading a headline maximum as universal. RUBI positions TX for intensive ceramic and porcelain cutting; no chip-free result is inferred. [28] [29] [30]
Before you choose
- Large capacity adds bulk, and the maximum thickness changes with the protector; ordinary backsplash tile rarely needs this whole setup. [28] [29] [30]
Check before buying:
- Large capacity adds bulk, and the maximum thickness changes with the protector; ordinary backsplash tile rarely needs this whole setup.
Model: 17910; inch-scale version with case · One selected cutter and named package; sizes and case variants not counted separately. · US
The details, side by side.
| What matters | #1RUBI SPEED-62 MAGNET | #2QEP 24-inch Professional Tile Cutter | #3Montolit Masterpiuma P5 63P5XL | #4Sigma Series 4 NEX 4BN | #5RUBI TS-43MAX | #6RUBI TR-600 MAGNET | #7Montolit MiniPiuma 26PBox | #8Sigma Series 4 UP 4BU | #9RUBI STAR-42 | #10RUBI TX-710MAX |
|---|---|---|---|---|---|---|---|---|---|---|
| Workflow | SPEED-62 MAGNET is our first choice for a mix of ordinary ceramic and porcelain backsplash cuts. The selected US 14988 package lists a 24-inch straight cut and 17-3/8-inch-square diagonal capacity; check the tile’s actual orientation before ordering. [1] | QEP 10630 is the choice for a buyer wanting side support and a simple rip/angle guide. Its feature section lists 24-inch straight cuts, 17.5-inch diagonal cuts and tile up to 1/2 inch thick, for most ceramic and porcelain. [4] | Masterpiuma P5 is the pick for repeated cuts across different tile thicknesses. Select the 63P5XL row in Montolit’s linked technical sheet: 63 cm straight, 44-by-44 cm diagonal and 20 mm maximum thickness. The page also refers to the shorter 63P5 family name; verify the supplied model. [7] | Sigma 4BN NEX is the push-handle specialist for a buyer considering structured tile. Sigma lists a 62 cm straight cut, 43.8 cm diagonal capacity and tile up to 19 mm thick. These are distinct from the dimensions of older NEX references. [10] | TS-43MAX suits small-format tile when a compact professional frame matters more than long rails. Its maker sheet lists 43 cm straight cuts, 30-by-30 cm diagonal cuts and a 6–15 mm thickness range. Thin tile below that range needs another choice. [13] | TR-600 MAGNET is our angled-layout choice when a swivelling measurement square is useful for repeat cuts. The selected US 17907 row lists 23-5/8-inch straight cuts and a 16.5-inch-square diagonal tile capacity, with a case included. [16] | MiniPiuma 26PBox is the compact kitchen-and-bathroom pick for smaller tile. Montolit’s technical table lists 36 cm straight cuts, 25-by-25 cm diagonal cuts and a 20 mm maximum thickness. The Box version is the selected package, not a second cutter recommendation. [19] | Sigma 4BU UP is the pull-scoring alternative to NEX. Its current model row lists 70 cm straight cuts, 49.5 cm diagonal capacity and a maximum tile thickness of 17 mm. Choose the scoring direction deliberately rather than treating UP and NEX as size variants. [22] | STAR-42 is the simpler compact choice for a ceramic backsplash. Its maker sheet lists 42 cm straight cuts, a 30-by-30 cm diagonal tile and 12 mm maximum thickness. RUBI describes professional ceramic use and occasional porcelain work. [25] | TX-710MAX is the specialist upgrade when backsplash tile shares a tool with longer or thicker renovation material. The maker sheet specifies 71 cm straight cuts and 50-by-50 cm diagonal capacity. It is more equipment than an ordinary small subway-tile job needs. [28] |
| Form factor | Its magnetic mobile breaker works along the cut rather than at one fixed breaking point. The maker lists dual 20 mm rails, a side stop for repeat cuts and a supplied 8 mm scoring wheel. The selected package includes a case. [2] | The current model has a 7/8-inch titanium-coated tungsten-carbide ball-bearing scoring wheel, dual chrome rails and a ball-bearing slide. QEP specifies replacement wheel 21125 and lists no carrying case. Confirm the current 10630 package rather than assuming legacy 10630Q contents. [5] | The P5 frame has side supports, a folding square for angle cuts up to 45 degrees in either direction and a handle with pressure indicators. Its instructions describe scoring toward the measuring guide, then using the handle for separation. These features do not constitute our accuracy test. [8] | The 16 mm scoring wheel runs on roller bearings with double suspension, which Sigma positions for structured surfaces. A 120 mm breaker foot has a replaceable anti-mark pad; the carriage uses three double-row bearings. Its handle can stay raised while positioning tile. [11] | The single-point fixed breaker distinguishes TS from RUBI’s mobile-breaker ranges. SMARTPOWER applies progressive breaking pressure; dual 17 mm rails sit over a steel base. RUBI lists 6 mm and 10 mm scoring wheels with the cutter and a case for the selected version. [14] | The mobile breaker uses a magnet system for one-handed operation. The rotating square separates its layout workflow from SPEED’s side-stop arrangement. RUBI lists an 800 kg separating-force figure; this is a manufacturer rating, not a measured finish or accuracy result. [17] | The small frame includes a protractor square for diagonal and repeat cuts. The maker lists the boxed version separately from the lighter unboxed 26P. Check storage dimensions and package contents rather than comparing the boxed weight with a bare competitor. [20] | The pull handle uses a 12 mm wheel and a 100 mm breaker foot with a replaceable anti-mark pad. Sigma lists three double-row carriage bearings and a raised handle position for placing tile. The visible wheel helps position the score line; we have not measured alignment accuracy. [23] | The cutter has dual rails, a mobile multipoint breaker, a cast-aluminium base and a supplied 6 mm scoring wheel. Select reference 14946 for the case; reference 14943 is the alternative without it. Those packaging choices are one physical cutter family. [26] | The mobile breaker has a ratchet lock and trigger release, with 30 mm tubular rails, floating tables, support arms and a pivoting square. The package includes 8 mm and 22 mm EXTREME PLUS scoring wheels and a case; check the PLUS wheel system when replacing them. [29] |
| Compatibility | RUBI’s metric sheet specifies a 3–15 mm thickness range. Choose a compatible wheel for the material; a longer rail and magnetic breaker do not establish a minimum strip width or successful snapping of every textured porcelain. Make trial cuts on the actual tile. [3] | The linked manual calls for one continuous scoring pass with medium pressure, followed by the prescribed breaking position. It says to clean rails with a dry cloth and not oil them. QEP’s lower specification table conflicts with its diagonal feature figure; use 17.5 inches conservatively and confirm fit with the seller. [6] | The manual includes handle adjustment and a lubricant-vial setup. MOSAKIT article 58 is an optional pad for the stated mosaic and delicate thin-glass applications; it is not assumed included. Match the accessory and tile instructions before using it on those materials. [9] | The suspended wheel is a design reason to consider NEX, not proof every relief or textured glaze will snap cleanly. Sigma lists the 64B2 magnetic mosaic mat as an accessory; do not infer that an unmodified cutter handles every sheet mosaic or glass tile. [12] | The maker positions TS for intensive ceramic and frequent porcelain cutting. Select the wheel and prescribed scoring/breaking setup for the tile. A fixed breaker and its force rating do not establish a usable minimum strip width or an edge finish on your particular backsplash. [15] | Check the tile thickness and scoring-wheel match against the exact TR package. The selected row lists 1/8–5/8 inch, while the introduction says up to 9/16 inch. Confirm the permitted thickness in the model instructions before buying near either limit. Neither the swivelling square nor the breaker makes outlet notches a score-and-snap operation. [18] | Montolit describes optional MOSAKIT article 58 for glass, ceramic and porcelain mosaic applications. That accessory matters: the base cutter alone is not our recommendation for arbitrary mesh-backed or glass mosaics. Confirm tile and pad compatibility, and try the actual sheet before committing the layout. [21] | The 64B2 magnetic mosaic mat and front-measurement accessories are separate options. Their listing does not show every mosaic will work on the bare machine. Wheel, tile surface and operator motion still need to suit the work; a familiar push stroke may make NEX a better personal fit. [24] | Choose STAR for straightforward ceramic cuts within its size rating, rather than assuming the occasional-porcelain description covers repeated dense porcelain. Confirm a suitable replacement wheel and actual tile fit. The modest frame is a different purchase from TS’s fixed-breaker setup, even though their straight capacities are close. [27] | The technical sheet distinguishes 3–19 mm tile with the protector from 3–21 mm without it. Plan around the protected 19 mm limit and follow the instructions rather than reading a headline maximum as universal. RUBI positions TX for intensive ceramic and porcelain cutting; no chip-free result is inferred. [30] |
Match the tile and scoring motion first
Measure the straight cut, diagonal tile and thickness separately. STAR’s 42 cm rail has a 30 cm-square diagonal limit, while TS starts at 6 mm thickness. Those details matter more than a force headline when fitting a thin or diagonal backsplash tile. [25] [13]
Try the scoring direction if possible: Sigma UP pulls a 12 mm wheel, while NEX pushes a suspended 16 mm wheel. A preference for one motion does not establish superior edge quality. QEP’s manual calls for one continuous score; follow the selected cutter’s instructions for pressure and breaking. [22] [23] [11] [6]
Plan mosaics, narrow pieces and cutouts separately
These choices cover straight score-and-snap work. Do not plan on using the breaker to form outlet notches or internal cutouts; arrange a separate cutting method for those shapes. For narrow strips and textured tile, try spare material before committing the layout. No minimum strip width or chip-free finish has been established here. [18] [3] [12]
Mosaic accessories are specific purchases. Montolit identifies optional MOSAKIT for the stated glass and mosaic uses; Sigma lists its own magnetic mosaic mat. Neither listing makes every unsupported sheet or glass tile suitable. Check the actual tile, accessory and wheel instructions together. QEP’s no-oil rail instruction should not be generalized to Montolit’s lubricant-vial setup. [21] [9] [24] [6]
How we compared.
Source-based comparison of manufacturer pages and selected technical sheets/manuals read October 22, 2026. In a Reddit Tile discussion, Wide_Lynx_2573 described disliking a pull cutter after using a push model. That individual preference supplies context for trying the scoring motion, not a test of the current Sigma models or owner consensus. We have not tested edge finish, narrow strips, breaking force or accuracy. Rankings emphasize distinct cutting and setup decisions independently of commission.
How we chooseSources
Official product documentation, reviewed October 22, 2026.
RUBI · US · Read October 22, 2026
QEP · US · Read October 22, 2026
Montolit · US · Read October 22, 2026
Sigma · US · Read October 22, 2026
RUBI · US · Read October 22, 2026
RUBI · US · Read October 22, 2026
Montolit · US · Read October 22, 2026
Sigma · US · Read October 22, 2026
RUBI · US · Read October 22, 2026
RUBI · US · Read October 22, 2026
RUBI · US · Read October 22, 2026
QEP · US · Read October 22, 2026
Montolit · US · Read October 22, 2026
Montolit · US · Read October 22, 2026
RUBI · US · Read October 22, 2026
Montolit · US · Read October 22, 2026
RUBI · US · Read October 22, 2026
Reddit r/Tile · US · Read October 22, 2026
Detailed source notes
- RUBI SPEED-62 MAGNET: SPEED-62 MAGNET is our first choice for a mix of ordinary ceramic and porcelain backsplash cuts. The selected US 14988 package lists a 24-inch straight cut and 17-3/8-inch-square diagonal capacity; check the tile’s actual orientation before ordering.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI SPEED-62 MAGNET official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
SPEED-62 MAGNET is our first choice for a mix of ordinary ceramic and porcelain backsplash cuts. The selected US 14988 package lists a 24-inch straight cut and 17-3/8-inch-square diagonal capacity; check the tile’s actual orientation before ordering.speed-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
SPEED-62 MAGNET is our first choice for a mix of ordinary ceramic and porcelain backsplash cuts. The selected US 14988 package lists a 24-inch straight cut and 17-3/8-inch-square diagonal capacity; check the tile’s actual orientation before ordering.Checked October 22, 2026
- RUBI SPEED-62 MAGNET: Its magnetic mobile breaker works along the cut rather than at one fixed breaking point. The maker lists dual 20 mm rails, a side stop for repeat cuts and a supplied 8 mm scoring wheel. The selected package includes a case.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI SPEED-62 MAGNET official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Its magnetic mobile breaker works along the cut rather than at one fixed breaking point. The maker lists dual 20 mm rails, a side stop for repeat cuts and a supplied 8 mm scoring wheel. The selected package includes a case.speed-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Its magnetic mobile breaker works along the cut rather than at one fixed breaking point. The maker lists dual 20 mm rails, a side stop for repeat cuts and a supplied 8 mm scoring wheel. The selected package includes a case.Checked October 22, 2026
- RUBI SPEED-62 MAGNET: RUBI’s metric sheet specifies a 3–15 mm thickness range. Choose a compatible wheel for the material; a longer rail and magnetic breaker do not establish a minimum strip width or successful snapping of every textured porcelain. Make trial cuts on the actual tile.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI SPEED-62 MAGNET official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
RUBI’s metric sheet specifies a 3–15 mm thickness range. Choose a compatible wheel for the material; a longer rail and magnetic breaker do not establish a minimum strip width or successful snapping of every textured porcelain. Make trial cuts on the actual tile.speed-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
RUBI’s metric sheet specifies a 3–15 mm thickness range. Choose a compatible wheel for the material; a longer rail and magnetic breaker do not establish a minimum strip width or successful snapping of every textured porcelain. Make trial cuts on the actual tile.Checked October 22, 2026
- QEP 24-inch Professional Tile Cutter: QEP 10630 is the choice for a buyer wanting side support and a simple rip/angle guide. Its feature section lists 24-inch straight cuts, 17.5-inch diagonal cuts and tile up to 1/2 inch thick, for most ceramic and porcelain.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
QEP 24-inch Professional Tile Cutter official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
QEP 10630 is the choice for a buyer wanting side support and a simple rip/angle guide. Its feature section lists 24-inch straight cuts, 17.5-inch diagonal cuts and tile up to 1/2 inch thick, for most ceramic and porcelain.qep-manual maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
QEP 10630 is the choice for a buyer wanting side support and a simple rip/angle guide. Its feature section lists 24-inch straight cuts, 17.5-inch diagonal cuts and tile up to 1/2 inch thick, for most ceramic and porcelain.Checked October 22, 2026
- QEP 24-inch Professional Tile Cutter: The current model has a 7/8-inch titanium-coated tungsten-carbide ball-bearing scoring wheel, dual chrome rails and a ball-bearing slide. QEP specifies replacement wheel 21125 and lists no carrying case. Confirm the current 10630 package rather than assuming legacy 10630Q contents.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
QEP 24-inch Professional Tile Cutter official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The current model has a 7/8-inch titanium-coated tungsten-carbide ball-bearing scoring wheel, dual chrome rails and a ball-bearing slide. QEP specifies replacement wheel 21125 and lists no carrying case. Confirm the current 10630 package rather than assuming legacy 10630Q contents.qep-manual maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The current model has a 7/8-inch titanium-coated tungsten-carbide ball-bearing scoring wheel, dual chrome rails and a ball-bearing slide. QEP specifies replacement wheel 21125 and lists no carrying case. Confirm the current 10630 package rather than assuming legacy 10630Q contents.Checked October 22, 2026
- QEP 24-inch Professional Tile Cutter: The linked manual calls for one continuous scoring pass with medium pressure, followed by the prescribed breaking position. It says to clean rails with a dry cloth and not oil them. QEP’s lower specification table conflicts with its diagonal feature figure; use 17.5 inches conservatively and confirm fit with the seller.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
QEP 24-inch Professional Tile Cutter official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The linked manual calls for one continuous scoring pass with medium pressure, followed by the prescribed breaking position. It says to clean rails with a dry cloth and not oil them. QEP’s lower specification table conflicts with its diagonal feature figure; use 17.5 inches conservatively and confirm fit with the seller.qep-manual maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The linked manual calls for one continuous scoring pass with medium pressure, followed by the prescribed breaking position. It says to clean rails with a dry cloth and not oil them. QEP’s lower specification table conflicts with its diagonal feature figure; use 17.5 inches conservatively and confirm fit with the seller.Checked October 22, 2026
- Montolit Masterpiuma P5 63P5XL: Masterpiuma P5 is the pick for repeated cuts across different tile thicknesses. Select the 63P5XL row in Montolit’s linked technical sheet: 63 cm straight, 44-by-44 cm diagonal and 20 mm maximum thickness. The page also refers to the shorter 63P5 family name; verify the supplied model.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Montolit Masterpiuma P5 63P5XL official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Masterpiuma P5 is the pick for repeated cuts across different tile thicknesses. Select the 63P5XL row in Montolit’s linked technical sheet: 63 cm straight, 44-by-44 cm diagonal and 20 mm maximum thickness. The page also refers to the shorter 63P5 family name; verify the supplied model.p5-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Masterpiuma P5 is the pick for repeated cuts across different tile thicknesses. Select the 63P5XL row in Montolit’s linked technical sheet: 63 cm straight, 44-by-44 cm diagonal and 20 mm maximum thickness. The page also refers to the shorter 63P5 family name; verify the supplied model.p5-manual maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Masterpiuma P5 is the pick for repeated cuts across different tile thicknesses. Select the 63P5XL row in Montolit’s linked technical sheet: 63 cm straight, 44-by-44 cm diagonal and 20 mm maximum thickness. The page also refers to the shorter 63P5 family name; verify the supplied model.Checked October 22, 2026
- Montolit Masterpiuma P5 63P5XL: The P5 frame has side supports, a folding square for angle cuts up to 45 degrees in either direction and a handle with pressure indicators. Its instructions describe scoring toward the measuring guide, then using the handle for separation. These features do not constitute our accuracy test.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Montolit Masterpiuma P5 63P5XL official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The P5 frame has side supports, a folding square for angle cuts up to 45 degrees in either direction and a handle with pressure indicators. Its instructions describe scoring toward the measuring guide, then using the handle for separation. These features do not constitute our accuracy test.p5-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The P5 frame has side supports, a folding square for angle cuts up to 45 degrees in either direction and a handle with pressure indicators. Its instructions describe scoring toward the measuring guide, then using the handle for separation. These features do not constitute our accuracy test.p5-manual maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The P5 frame has side supports, a folding square for angle cuts up to 45 degrees in either direction and a handle with pressure indicators. Its instructions describe scoring toward the measuring guide, then using the handle for separation. These features do not constitute our accuracy test.Checked October 22, 2026
- Montolit Masterpiuma P5 63P5XL: The manual includes handle adjustment and a lubricant-vial setup. MOSAKIT article 58 is an optional pad for the stated mosaic and delicate thin-glass applications; it is not assumed included. Match the accessory and tile instructions before using it on those materials.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Montolit Masterpiuma P5 63P5XL official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The manual includes handle adjustment and a lubricant-vial setup. MOSAKIT article 58 is an optional pad for the stated mosaic and delicate thin-glass applications; it is not assumed included. Match the accessory and tile instructions before using it on those materials.p5-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The manual includes handle adjustment and a lubricant-vial setup. MOSAKIT article 58 is an optional pad for the stated mosaic and delicate thin-glass applications; it is not assumed included. Match the accessory and tile instructions before using it on those materials.p5-manual maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The manual includes handle adjustment and a lubricant-vial setup. MOSAKIT article 58 is an optional pad for the stated mosaic and delicate thin-glass applications; it is not assumed included. Match the accessory and tile instructions before using it on those materials.Checked October 22, 2026
- Sigma Series 4 NEX 4BN: Sigma 4BN NEX is the push-handle specialist for a buyer considering structured tile. Sigma lists a 62 cm straight cut, 43.8 cm diagonal capacity and tile up to 19 mm thick. These are distinct from the dimensions of older NEX references.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Sigma Series 4 NEX 4BN official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Sigma 4BN NEX is the push-handle specialist for a buyer considering structured tile. Sigma lists a 62 cm straight cut, 43.8 cm diagonal capacity and tile up to 19 mm thick. These are distinct from the dimensions of older NEX references.Checked October 22, 2026
- Sigma Series 4 NEX 4BN: The 16 mm scoring wheel runs on roller bearings with double suspension, which Sigma positions for structured surfaces. A 120 mm breaker foot has a replaceable anti-mark pad; the carriage uses three double-row bearings. Its handle can stay raised while positioning tile.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Sigma Series 4 NEX 4BN official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The 16 mm scoring wheel runs on roller bearings with double suspension, which Sigma positions for structured surfaces. A 120 mm breaker foot has a replaceable anti-mark pad; the carriage uses three double-row bearings. Its handle can stay raised while positioning tile.Checked October 22, 2026
- Sigma Series 4 NEX 4BN: The suspended wheel is a design reason to consider NEX, not proof every relief or textured glaze will snap cleanly. Sigma lists the 64B2 magnetic mosaic mat as an accessory; do not infer that an unmodified cutter handles every sheet mosaic or glass tile.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Sigma Series 4 NEX 4BN official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The suspended wheel is a design reason to consider NEX, not proof every relief or textured glaze will snap cleanly. Sigma lists the 64B2 magnetic mosaic mat as an accessory; do not infer that an unmodified cutter handles every sheet mosaic or glass tile.Checked October 22, 2026
- RUBI TS-43MAX: TS-43MAX suits small-format tile when a compact professional frame matters more than long rails. Its maker sheet lists 43 cm straight cuts, 30-by-30 cm diagonal cuts and a 6–15 mm thickness range. Thin tile below that range needs another choice.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI TS-43MAX official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
TS-43MAX suits small-format tile when a compact professional frame matters more than long rails. Its maker sheet lists 43 cm straight cuts, 30-by-30 cm diagonal cuts and a 6–15 mm thickness range. Thin tile below that range needs another choice.ts-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
TS-43MAX suits small-format tile when a compact professional frame matters more than long rails. Its maker sheet lists 43 cm straight cuts, 30-by-30 cm diagonal cuts and a 6–15 mm thickness range. Thin tile below that range needs another choice.Checked October 22, 2026
- RUBI TS-43MAX: The single-point fixed breaker distinguishes TS from RUBI’s mobile-breaker ranges. SMARTPOWER applies progressive breaking pressure; dual 17 mm rails sit over a steel base. RUBI lists 6 mm and 10 mm scoring wheels with the cutter and a case for the selected version.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI TS-43MAX official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The single-point fixed breaker distinguishes TS from RUBI’s mobile-breaker ranges. SMARTPOWER applies progressive breaking pressure; dual 17 mm rails sit over a steel base. RUBI lists 6 mm and 10 mm scoring wheels with the cutter and a case for the selected version.ts-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The single-point fixed breaker distinguishes TS from RUBI’s mobile-breaker ranges. SMARTPOWER applies progressive breaking pressure; dual 17 mm rails sit over a steel base. RUBI lists 6 mm and 10 mm scoring wheels with the cutter and a case for the selected version.Checked October 22, 2026
- RUBI TS-43MAX: The maker positions TS for intensive ceramic and frequent porcelain cutting. Select the wheel and prescribed scoring/breaking setup for the tile. A fixed breaker and its force rating do not establish a usable minimum strip width or an edge finish on your particular backsplash.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI TS-43MAX official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The maker positions TS for intensive ceramic and frequent porcelain cutting. Select the wheel and prescribed scoring/breaking setup for the tile. A fixed breaker and its force rating do not establish a usable minimum strip width or an edge finish on your particular backsplash.ts-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The maker positions TS for intensive ceramic and frequent porcelain cutting. Select the wheel and prescribed scoring/breaking setup for the tile. A fixed breaker and its force rating do not establish a usable minimum strip width or an edge finish on your particular backsplash.Checked October 22, 2026
- RUBI TR-600 MAGNET: TR-600 MAGNET is our angled-layout choice when a swivelling measurement square is useful for repeat cuts. The selected US 17907 row lists 23-5/8-inch straight cuts and a 16.5-inch-square diagonal tile capacity, with a case included.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI TR-600 MAGNET official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
TR-600 MAGNET is our angled-layout choice when a swivelling measurement square is useful for repeat cuts. The selected US 17907 row lists 23-5/8-inch straight cuts and a 16.5-inch-square diagonal tile capacity, with a case included.Checked October 22, 2026
- RUBI TR-600 MAGNET: The mobile breaker uses a magnet system for one-handed operation. The rotating square separates its layout workflow from SPEED’s side-stop arrangement. RUBI lists an 800 kg separating-force figure; this is a manufacturer rating, not a measured finish or accuracy result.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI TR-600 MAGNET official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The mobile breaker uses a magnet system for one-handed operation. The rotating square separates its layout workflow from SPEED’s side-stop arrangement. RUBI lists an 800 kg separating-force figure; this is a manufacturer rating, not a measured finish or accuracy result.Checked October 22, 2026
- RUBI TR-600 MAGNET: Check the tile thickness and scoring-wheel match against the exact TR package. The selected row lists 1/8–5/8 inch, while the introduction says up to 9/16 inch. Confirm the permitted thickness in the model instructions before buying near either limit. Neither the swivelling square nor the breaker makes outlet notches a score-and-snap operation.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI TR-600 MAGNET official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Check the tile thickness and scoring-wheel match against the exact TR package. The selected row lists 1/8–5/8 inch, while the introduction says up to 9/16 inch. Confirm the permitted thickness in the model instructions before buying near either limit. Neither the swivelling square nor the breaker makes outlet notches a score-and-snap operation.Checked October 22, 2026
- Montolit MiniPiuma 26PBox: MiniPiuma 26PBox is the compact kitchen-and-bathroom pick for smaller tile. Montolit’s technical table lists 36 cm straight cuts, 25-by-25 cm diagonal cuts and a 20 mm maximum thickness. The Box version is the selected package, not a second cutter recommendation.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Montolit MiniPiuma 26PBox official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
MiniPiuma 26PBox is the compact kitchen-and-bathroom pick for smaller tile. Montolit’s technical table lists 36 cm straight cuts, 25-by-25 cm diagonal cuts and a 20 mm maximum thickness. The Box version is the selected package, not a second cutter recommendation.mini-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
MiniPiuma 26PBox is the compact kitchen-and-bathroom pick for smaller tile. Montolit’s technical table lists 36 cm straight cuts, 25-by-25 cm diagonal cuts and a 20 mm maximum thickness. The Box version is the selected package, not a second cutter recommendation.Checked October 22, 2026
- Montolit MiniPiuma 26PBox: The small frame includes a protractor square for diagonal and repeat cuts. The maker lists the boxed version separately from the lighter unboxed 26P. Check storage dimensions and package contents rather than comparing the boxed weight with a bare competitor.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Montolit MiniPiuma 26PBox official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The small frame includes a protractor square for diagonal and repeat cuts. The maker lists the boxed version separately from the lighter unboxed 26P. Check storage dimensions and package contents rather than comparing the boxed weight with a bare competitor.mini-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The small frame includes a protractor square for diagonal and repeat cuts. The maker lists the boxed version separately from the lighter unboxed 26P. Check storage dimensions and package contents rather than comparing the boxed weight with a bare competitor.Checked October 22, 2026
- Montolit MiniPiuma 26PBox: Montolit describes optional MOSAKIT article 58 for glass, ceramic and porcelain mosaic applications. That accessory matters: the base cutter alone is not our recommendation for arbitrary mesh-backed or glass mosaics. Confirm tile and pad compatibility, and try the actual sheet before committing the layout.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Montolit MiniPiuma 26PBox official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Montolit describes optional MOSAKIT article 58 for glass, ceramic and porcelain mosaic applications. That accessory matters: the base cutter alone is not our recommendation for arbitrary mesh-backed or glass mosaics. Confirm tile and pad compatibility, and try the actual sheet before committing the layout.mini-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Montolit describes optional MOSAKIT article 58 for glass, ceramic and porcelain mosaic applications. That accessory matters: the base cutter alone is not our recommendation for arbitrary mesh-backed or glass mosaics. Confirm tile and pad compatibility, and try the actual sheet before committing the layout.Checked October 22, 2026
- Sigma Series 4 UP 4BU: Sigma 4BU UP is the pull-scoring alternative to NEX. Its current model row lists 70 cm straight cuts, 49.5 cm diagonal capacity and a maximum tile thickness of 17 mm. Choose the scoring direction deliberately rather than treating UP and NEX as size variants.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Sigma Series 4 UP 4BU official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Sigma 4BU UP is the pull-scoring alternative to NEX. Its current model row lists 70 cm straight cuts, 49.5 cm diagonal capacity and a maximum tile thickness of 17 mm. Choose the scoring direction deliberately rather than treating UP and NEX as size variants.Checked October 22, 2026
- Sigma Series 4 UP 4BU: The pull handle uses a 12 mm wheel and a 100 mm breaker foot with a replaceable anti-mark pad. Sigma lists three double-row carriage bearings and a raised handle position for placing tile. The visible wheel helps position the score line; we have not measured alignment accuracy.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Sigma Series 4 UP 4BU official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The pull handle uses a 12 mm wheel and a 100 mm breaker foot with a replaceable anti-mark pad. Sigma lists three double-row carriage bearings and a raised handle position for placing tile. The visible wheel helps position the score line; we have not measured alignment accuracy.Checked October 22, 2026
- Sigma Series 4 UP 4BU: The 64B2 magnetic mosaic mat and front-measurement accessories are separate options. Their listing does not show every mosaic will work on the bare machine. Wheel, tile surface and operator motion still need to suit the work; a familiar push stroke may make NEX a better personal fit.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
Sigma Series 4 UP 4BU official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The 64B2 magnetic mosaic mat and front-measurement accessories are separate options. Their listing does not show every mosaic will work on the bare machine. Wheel, tile surface and operator motion still need to suit the work; a familiar push stroke may make NEX a better personal fit.Checked October 22, 2026
- RUBI STAR-42: STAR-42 is the simpler compact choice for a ceramic backsplash. Its maker sheet lists 42 cm straight cuts, a 30-by-30 cm diagonal tile and 12 mm maximum thickness. RUBI describes professional ceramic use and occasional porcelain work.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI STAR-42 official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
STAR-42 is the simpler compact choice for a ceramic backsplash. Its maker sheet lists 42 cm straight cuts, a 30-by-30 cm diagonal tile and 12 mm maximum thickness. RUBI describes professional ceramic use and occasional porcelain work.Checked October 22, 2026
- RUBI STAR-42: The cutter has dual rails, a mobile multipoint breaker, a cast-aluminium base and a supplied 6 mm scoring wheel. Select reference 14946 for the case; reference 14943 is the alternative without it. Those packaging choices are one physical cutter family.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI STAR-42 official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The cutter has dual rails, a mobile multipoint breaker, a cast-aluminium base and a supplied 6 mm scoring wheel. Select reference 14946 for the case; reference 14943 is the alternative without it. Those packaging choices are one physical cutter family.Checked October 22, 2026
- RUBI STAR-42: Choose STAR for straightforward ceramic cuts within its size rating, rather than assuming the occasional-porcelain description covers repeated dense porcelain. Confirm a suitable replacement wheel and actual tile fit. The modest frame is a different purchase from TS’s fixed-breaker setup, even though their straight capacities are close.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI STAR-42 official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
Choose STAR for straightforward ceramic cuts within its size rating, rather than assuming the occasional-porcelain description covers repeated dense porcelain. Confirm a suitable replacement wheel and actual tile fit. The modest frame is a different purchase from TS’s fixed-breaker setup, even though their straight capacities are close.Checked October 22, 2026
- RUBI TX-710MAX: TX-710MAX is the specialist upgrade when backsplash tile shares a tool with longer or thicker renovation material. The maker sheet specifies 71 cm straight cuts and 50-by-50 cm diagonal capacity. It is more equipment than an ordinary small subway-tile job needs.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI TX-710MAX official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
TX-710MAX is the specialist upgrade when backsplash tile shares a tool with longer or thicker renovation material. The maker sheet specifies 71 cm straight cuts and 50-by-50 cm diagonal capacity. It is more equipment than an ordinary small subway-tile job needs.tx-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
TX-710MAX is the specialist upgrade when backsplash tile shares a tool with longer or thicker renovation material. The maker sheet specifies 71 cm straight cuts and 50-by-50 cm diagonal capacity. It is more equipment than an ordinary small subway-tile job needs.Checked October 22, 2026
- RUBI TX-710MAX: The mobile breaker has a ratchet lock and trigger release, with 30 mm tubular rails, floating tables, support arms and a pivoting square. The package includes 8 mm and 22 mm EXTREME PLUS scoring wheels and a case; check the PLUS wheel system when replacing them.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI TX-710MAX official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The mobile breaker has a ratchet lock and trigger release, with 30 mm tubular rails, floating tables, support arms and a pivoting square. The package includes 8 mm and 22 mm EXTREME PLUS scoring wheels and a case; check the PLUS wheel system when replacing them.tx-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The mobile breaker has a ratchet lock and trigger release, with 30 mm tubular rails, floating tables, support arms and a pivoting square. The package includes 8 mm and 22 mm EXTREME PLUS scoring wheels and a case; check the PLUS wheel system when replacing them.Checked October 22, 2026
- RUBI TX-710MAX: The technical sheet distinguishes 3–19 mm tile with the protector from 3–21 mm without it. Plan around the protected 19 mm limit and follow the instructions rather than reading a headline maximum as universal. RUBI positions TX for intensive ceramic and porcelain cutting; no chip-free result is inferred.
Exact selected model and maker-rated cutting mode. Straight length, square diagonal size and thickness are separate. Match tile, surface, scoring wheel, support, accessories and instructions; no measured finish, minimum-strip width or universal glass/mosaic compatibility inferred.
RUBI TX-710MAX official model details · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The technical sheet distinguishes 3–19 mm tile with the protector from 3–21 mm without it. Plan around the protected 19 mm limit and follow the instructions rather than reading a headline maximum as universal. RUBI positions TX for intensive ceramic and porcelain cutting; no chip-free result is inferred.tx-sheet maker technical documentation · Actual selected model/features table or identified technical sheet/manual read; original factual notes retained.
The technical sheet distinguishes 3–19 mm tile with the protector from 3–21 mm without it. Plan around the protected 19 mm limit and follow the instructions rather than reading a headline maximum as universal. RUBI positions TX for intensive ceramic and porcelain cutting; no chip-free result is inferred.Checked October 22, 2026